A vintage Wm Marples & sons Beechwood marking gauge marked Sheffield England. The Logo is faint but readable and the markings are very good.

$17.00

Although unmarked I believe this is a Hercules Bob. Crisp ccondition brass with a steel point overall length 4" and weighs about 1/2lb.

$25.00

Stanley No.0 30" level. Made in Canada. The level is marked Genuine Cherry Best Wood for Levels In very good condition.

$28.00

This Beechwood marking gauge has a Brass "moustache" wear plate. In good+ condition with legible markings.

$16.00

This one is in pristine condition. Ready for use or show, I doubt that the string is original.

$19.00

A handy little level for the shop apron.

$8.00

good working order very nice english marking gauge

 $55.00

Sorry but the blade was too rusted to get a makers name but I believe it's a Stanley. The Rosewood and brass are in very good condition. The blade is badly pitted but I managed to buff it to a usable state. With a short 6in blade this is a very handy bevel for the shop.

$19.00

Older unmarked cast iron plumb bob in good condition. It has a newer paint job but is in good++ condition. I believe it may be from Taylor-Forbes of Guelph Ontario.

$14.00

A great little marking gauge this. Marked  H Disston & Sons Philla USA it appears to be Mahogany in construction with 2 brass wear strips and a great brass setting screw.There are no factory measurements on it.

$25.00

Stamped W Marples&sons sheffield Eng  Very nice $37.00

For the old school engineer. This precision slide rule made by Sterling is in as new condition 11" in length and comes with the original protective sleeve. Pull this out in the office and baffle the new grads.

$12.00

I was told this fine plumb bob was purchased at Sears over 30 years ago. In extra fine condition ready to use or add to the collection.

$17.00

Stanley NO84 E SW  $50.00

Just a very nice Stanley bevel guage in near mint condition.

$18.00

A nice old set of unsigned iron dividers. Legs 7" long and a spread of 10" with a brass pivot. Clean and ready to use.

$15.00

Nice and clean 6 foot folding ruler.

$8.00

A nice small set of outside calipers from Moore and Wright of Sheffield England one of the worlds best makers of measuring tools. A nice size for the shop apron.  This set of outside calipers are 4 1/2" high with a capacity of 4 1/2"

$15.00

A nice machinist caliper rule here. Made by Somet and in very good condition with case. 10" in length

$15.00

Stanley 53 1/2 Architect's rule SW logo

 $95.00

Stanley SW NO84 Brass bound nice $45.00

nice little square

 $25.00

A fine set of inside calipers from Union Tool Co. Max opening size is 4 1/2" in good++ condition and ready to use.

$12.00

Here's a chance to own a classic. This type 1 30" level from Cook-Davis of Watertown NY is in good++ condition. A tiny slice of wood missing on the bottom plate and the usual scratches are the only apologies visible here. The top plate reads Cook's Patent Level Pat.d Dec.7 1886 Manufactured by Davis & Cook Watertown NY USA and it has 2 adjusting screws. Top plate and vial rings are nickle plated as are the end caps.

$60.00

A great Stanley #41 level. This little beauty is 3 1/2" long made of cast iron with a decorative brass top plate. It is made to be used screwed to a square. The vial is intact and the lever in excellent condition.

$35.00

This is one beautiful plumb bob. Unsigned but definitely made by a craftsman. The machining is fantastic and the proportions artllike. A treasure for any tool chest or collection.

$35.00

                             To place an order                                   

darbystools@gmail.com